Wind turbines do work; put them in nice, smooth air and their energy production is quite predictable (we will get to predicting it a bit further on in this story). The honest manufacturers do not lie or exaggerate, their turbines really can work as advertised in smooth, laminar airflow. However, put that same turbine on a 40 feet tower and even if the annual average wind speed is still 5 m/s at that height, its energy production will fall far short of what you would predict for that value. How short is anybody’s guess, that is part of the point; it is impossible to predict the effect of turbulence other than that it robs the energy production potential of any wind turbine. Roof tops, or other locations on a house, make for poor turbine sites. They are usually very turbulent and on top of that their average wind speeds are usually very low.
A regular alternator out of a car needs to be modified to produce anything meaningful above a few volts if any at low RPM. If this guy is not totally bullshit lieing, he is using a modified PMA alternator (permanent magnet alternator) and if not the voltage he is so proudly showing is actually a voltage drop caused by the alternator using power to power it's field coil. This is very misleading to newcomers to the field of renewable energy and makes a mockery of it. And if he really wanted to help people build this he would have should people how to wire the alternator up . Including explaining things like the wires on the regulator the ignition switch , the stator and the field wires. This is why rednecks laugh at liberals because they see shit like this. .
America is embracing renewables, slowly. In 2016, Massachusetts passed a law promoting a huge investment in wind and hydropower; the first megawatt is expected to hit the grid in 2020. Early this year New York State announced plans to spend 12 years building the infrastructure for a $6 billion offshore wind power industry. Hawaii has pledged to be powered entirely by renewable energy—in 2045. Atlanta’s goal is 2035 and San Francisco’s is 2030. Typically, plans to convert to sustainable energy stretch on for decades.
Green energy, however, utilizes energy sources that are readily available all over the world, including in rural and remote areas that don't otherwise have access to electricity. Advances in renewable energy technologies have lowered the cost of solar panels, wind turbines and other sources of green energy, placing the ability to produce electricity in the hands of the people rather than those of oil, gas, coal and utility companies.

The combination of wind and solar PV has the advantage that the two sources complement each other because the peak operating times for each system occur at different times of the day and year. The power generation of such solar hybrid power systems is therefore more constant and fluctuates less than each of the two component subsystems.[21] Solar power is seasonal, particularly in northern/southern climates, away from the equator, suggesting a need for long term seasonal storage in a medium such as hydrogen or pumped hydroelectric.[117] The Institute for Solar Energy Supply Technology of the University of Kassel pilot-tested a combined power plant linking solar, wind, biogas and hydrostorage to provide load-following power from renewable sources.[118]
Wind power first appeared in Europe during the Middle Ages. The first historical records of their use in England date to the 11th or 12th centuries and there are reports of German crusaders taking their windmill-making skills to Syria around 1190.[6] By the 14th century, Dutch windmills were in use to drain areas of the Rhine delta. Advanced wind turbines were described by Croatian inventor Fausto Veranzio. In his book Machinae Novae (1595) he described vertical axis wind turbines with curved or V-shaped blades.
The Sunforce 44444 400 Watt Wind Generator uses wind to generate power and run your appliances and electronics. Constructed from lightweight, weatherproof cast aluminum, this generator is also a great choice for powering pumps or charging batteries for large power demands. With a maximum power up to 400 watts or 27 amps, this device features a fully integrated regulator that automatically shuts down when the batteries are completely charged. The 44444 is virtually maintenance free with only two moving parts, and the carbon fiber composite blades ensure low wind noise while the patented high wind over speed technology guarantees a smooth, clean charge. Assembly is required, but this generator installs easily and mounts to any sturdy pole, building, or the Sunforce 44455 Wind Generator 30-Foot Tower Kit. The 44444 uses a 12-volt battery (not included) and measures 27 x 44 x 44 inches (LxWxH)
The conversion of sunlight into electricity is made possible with the special properties of semi-conducting materials. It can be harnessed through a range of ever-evolving technologies like solar heating, photovoltaics, solar thermal energy, solar architecture, molten salt power plants, and artificial photosynthesis. Learn more about solar solutions from IGS Solar.

As competition in the wind market increases, companies are seeking ways to draw greater efficiency from their designs. One of the predominant ways wind turbines have gained performance is by increasing rotor diameters, and thus blade length. Retrofitting current turbines with larger blades mitigates the need and risks associated with a system-level redesign. As the size of the blade increases, its tendency to deflect also increases. Thus, from a materials perspective, the stiffness-to-weight is of major importance. As the blades need to function over a 100 million load cycles over a period of 20–25 years, the fatigue life of the blade materials is also of utmost importance. By incorporating carbon fiber into parts of existing blade systems, manufacturers may increase the length of the blades without increasing their overall weight. For instance, the spar cap, a structural element of a turbine blade, commonly experiences high tensile loading, making it an ideal candidate to utilize the enhanced tensile properties of carbon fiber in comparison to glass fiber.[47] Higher stiffness and lower density translates to thinner, lighter blades offering equivalent performance. In a 10 (MW) turbine—which will become more common in offshore systems by 2021—blades may reach over 100 m in length and weigh up to 50 metric tons when fabricated out of glass fiber. A switch to carbon fiber in the structural spar of the blade yields weight savings of 20 to 30 percent, or approximately 15 metric tons.[48]


These high strength magnets are usually made from rare earth materials such as neodymium iron (NdFe), or samarium cobalt (SmCo) eliminating the need for the field windings to provide a constant magnetic field, leading to a simpler, more rugged construction. Wound field windings have the advantage of matching their magnetism (and therefore power) with the varying wind speed but require an external energy source to generate the required magnetic field.
Then the faster the coil of wire rotates, the greater the rate of change by which the magnetic flux is cut by the coil and the greater is the induced emf within the coil. Similarly, if the magnetic field is made stronger, the induced emf will increase for the same rotational speed. Thus: emf ∝ Φn. Where: “Φ” is the magnetic-field flux and “n” is the speed of rotation. Also, the polarity of the generated voltage depends on the direction of the magnetic lines of flux and the direction of movement of the conductor.
Perfect for camping tailgating or when you need Perfect for camping tailgating or when you need power on the go. The FIRMAN P01001 generator features 1050 starting Watts and 1300 running watts. Power is supplied by our Max Pro Series 80cc FIRMAN engine which runs cool and efficient thanks to its Phoenix Fat Head Block. Our Whisper Series ...  More + Product Details Close

Kinetic Internal Thermal Potential Gravitational Elastic Electrical potential energy Mechanical Interatomic potential Electrical Magnetic Ionization Radiant Binding Nuclear binding energy Gravitational binding energy Chromodynamic Dark Quintessence Phantom Negative Chemical Rest Sound energy Surface energy Mechanical wave Sound wave Vacuum energy Zero-point energy


Home wind turbines are electric generators that convert wind energy into clean, emission-free power. Although most large wind farms exist to power certain towns and communities, there are also smaller wind turbines for homes and homeowners. These smaller turbines can be installed on any part of your property to cover some or even all of your monthly energy needs.

A subtype of Darrieus turbine with straight, as opposed to curved, blades. The cycloturbine variety has variable pitch to reduce the torque pulsation and is self-starting.[33] The advantages of variable pitch are: high starting torque; a wide, relatively flat torque curve; a higher coefficient of performance; more efficient operation in turbulent winds; and a lower blade speed ratio which lowers blade bending stresses. Straight, V, or curved blades may be used.[34]
A wind turbine is made up of two major components and having looked at one of them, the rotor blade design in the previous tutorial, we can now look at the other, the Wind Turbine Generator or WTG’s which is the electrical machine used to generate the electricity. A low rpm electrical generator is used for converting the mechanical rotational power produced by the winds energy into usable electricity to supply our homes and is at the heart of any wind power system.
Several large-scale energy storage suggestions for the grid have been done. Worldwide there is over 100 GW of Pumped-storage hydroelectricity. This improves efficiency and decreases energy losses but a conversion to an energy storing mains electricity grid is a very costly solution. Some costs could potentially be reduced by making use of energy storage equipment the consumer buys and not the state. An example is batteries in electric cars that would double as an energy buffer for the electricity grid. However besides the cost, setting-up such a system would still be a very complicated and difficult procedure. Also, energy storage apparatus' as car batteries are also built with materials that pose a threat to the environment (e.g. Lithium). The combined production of batteries for such a large part of the population would still have environmental concerns. Besides car batteries however, other Grid energy storage projects make use of less polluting energy carriers (e.g. compressed air tanks and flywheel energy storage).
Previously, the largest U.S. city fully powered by renewables was Burlington, Vermont (pop. 42,000), home to Senator Bernie Sanders, the jam band Phish and the original Ben & Jerry’s. Georgetown’s feat is all the more dramatic because it demolishes the notion that sustainability is synonymous with socialism and GMO-free ice cream. “You think of climate change and renewable energy, from a political standpoint, on the left-hand side of the spectrum, and what I’ve done is toss all those partisan political thoughts aside,” Ross says. “We’re doing this because it’s good for our citizens. Cheaper electricity is better. Clean energy is better than fossil fuels.”
A turbine that produces around 5 kW worth of energy can produce approximately 8,000 kWh per year, assuming there are decent winds to power it. Given ideal conditions, you will be able to recoup your investment in three to five years, depending on your monthly energy consumption and other related factors. If, however, your property doesn’t get enough wind then it may take a little more time to recover your initial investment.

By clicking above, you authorize Solar Power Authority and up to four Solar Companies to call you and send you pre-recorded messages and text messages at the number you entered above, using an autodialer, with offers about their products or services, even if your phone number is on any national or state “Do Not Call” list. Message and data rates may apply. Your consent here is not based on a condition of purchase.


“New Wind May Be Cheaper than Old, Reliable Coal” • Wind farms have cost less to build and operate than coal-fired power plants for some time. The trend of lower costs for renewables has crossed a threshold: it is sometimes cheaper to build a brand new wind facility than keep an old coal plant burning, according to Lazard Ltd. [Casper Star-Tribune Online]
Because one obstacle to adopting wind and solar power is reliability—what happens on calm, cloudy days?—recent improvements in energy-storage technology, a.k.a. batteries, are helping accelerate adoption of renewables. Last May, for example, Tucson Electric Power signed a deal for solar energy with storage, which can mitigate (if not entirely resolve) concerns about how to provide power on gray days. The storage upped the energy cost by $15 per megawatt hour. By the end of the year, the Public Service Company of Colorado had been quoted a storage fee that increased the cost of a megawatt hour by only $3 to $7, a drop of more than 50 percent. In a landmark achievement, Tesla installed the world’s largest lithium-ion battery in South Australia last December, to store wind-generated power. But by then Hyundai Electric was at work in the South Korean metropolis of Ulsan on a battery that was 50 percent bigger.

In net metering the price of the electricity produced is the same as the price supplied to the consumer, and the consumer is billed on the difference between production and consumption. Net metering can usually be done with no changes to standard electricity meters, which accurately measure power in both directions and automatically report the difference, and because it allows homeowners and businesses to generate electricity at a different time from consumption, effectively using the grid as a giant storage battery. With net metering, deficits are billed each month while surpluses are rolled over to the following month. Best practices call for perpetual roll over of kWh credits.[97] Excess credits upon termination of service are either lost, or paid for at a rate ranging from wholesale to retail rate or above, as can be excess annual credits. In New Jersey, annual excess credits are paid at the wholesale rate, as are left over credits when a customer terminates service.[98]
One issue that has often raised concerns is the use of cadmium (Cd), a toxic heavy metal that has the tendency to accumulate in ecological food chains. It is used as semiconductor component in CdTe solar cells and as buffer layer for certain CIGS cells in the form of CdS.[141] The amount of cadmium used in thin-film PV modules is relatively small (5–10 g/m²) and with proper recycling and emission control techniques in place the cadmium emissions from module production can be almost zero. Current PV technologies lead to cadmium emissions of 0.3–0.9 microgram/kWh over the whole life-cycle.[121] Most of these emissions arise through the use of coal power for the manufacturing of the modules, and coal and lignite combustion leads to much higher emissions of cadmium. Life-cycle cadmium emissions from coal is 3.1 microgram/kWh, lignite 6.2, and natural gas 0.2 microgram/kWh.

The conversion of the rotational mechanical power generated by the rotor blades (known as the prime mover) into useful electrical power for use in domestic power and lighting applications or to charge batteries can be accomplished by any one of the following major types of rotational electrical machines commonly used in a wind power generating systems:
In 2015, Ross wrote an op-ed for Time magazine about his city’s planned transition to renewables. “A town in the middle of a state that recently sported oil derricks on its license plates may not be where you’d expect to see leaders move to clean solar and wind generation,” he wrote. Lest readers get the wrong idea, he felt compelled to explain: “No, environmental zealots have not taken over City Council.”
Due to increased technology and wide implementation, the global glass fiber market might reach US$17.4 billion by 2024, compared to US$8.5 billion in 2014. Since it is the most widely used material for reinforcement in composites around the globe, the expansion of end use applications such as construction, transportation and wind turbines has fueled its popularity. Asia Pacific held the major share of the global market in 2014 with more than 45% volume share. However China is currently the largest producer. The industry receives subsidies from the Chinese government allowing them to export it cheaper to the US and Europe. However, due to the higher demand in the near future some price wars have started to developed to implement anti dumping strategies such as tariffs on Chinese glass fiber.[58]
Wind is a form of solar energy and is a result of the uneven heating of the atmosphere by the sun, the irregularities of the earth's surface, and the rotation of the earth. Wind flow patterns and speeds vary greatly across the United States and are modified by bodies of water, vegetation, and differences in terrain. Humans use this wind flow, or motion energy, for many purposes: sailing, flying a kite, and even generating electricity.
Taken together, the generation and distribution of electric power in the United States is an astonishingly complex undertaking. Utilities may generate their own power or buy it from other utilities; that power travels over a grid of transformers and high- and low-voltage lines to your house. Ownership of utilities varies from nonprofits to cooperatives to for-profits. Federal regulators ultimately oversee the grid. Amazingly, when you flip a switch, electricity is there.
The oldest solar thermal power plant in the world is the 354 megawatt (MW) SEGS thermal power plant, in California.[109] The Ivanpah Solar Electric Generating System is a solar thermal power project in the California Mojave Desert, 40 miles (64 km) southwest of Las Vegas, with a gross capacity of 377 MW.[110] The 280 MW Solana Generating Station is a solar power plant near Gila Bend, Arizona, about 70 miles (110 km) southwest of Phoenix, completed in 2013. When commissioned it was the largest parabolic trough plant in the world and the first U.S. solar plant with molten salt thermal energy storage.[111]

Jump up ^ Noth, André (July 2008). "History of Solar Flight" (PDF). Autonomous Systems Lab. Zürich: Swiss Federal Institute of Technology. p. 3. Archived from the original (PDF) on 1 February 2012. Retrieved 8 July 2010. Günter Rochelt was the designer and builder of Solair I, a 16 m wingspan solar airplane ... 21st of August 1983 he flew in Solair I, mostly on solar energy and also thermals, during 5 hours 41 minutes.

A turbine that produces around 5 kW worth of energy can produce approximately 8,000 kWh per year, assuming there are decent winds to power it. Given ideal conditions, you will be able to recoup your investment in three to five years, depending on your monthly energy consumption and other related factors. If, however, your property doesn’t get enough wind then it may take a little more time to recover your initial investment.


There are more specific questions you’ll have to ask yourself about your location and home—e.g., is my next-door neighbor’s oak tree going to block all my sunlight? You’ll also have to take local weather conditions into consideration. Luckily, there are plenty of other resources to help you find your solar potential. See our Tools section for more info.
Construction of the Salt Tanks which provide efficient thermal energy storage[103] so that output can be provided after the sun goes down, and output can be scheduled to meet demand requirements.[104] The 280 MW Solana Generating Station is designed to provide six hours of energy storage. This allows the plant to generate about 38 percent of its rated capacity over the course of a year.[105]
Green energy is commonly thought of in the context of electricity, mechanical power, heating and cogeneration. Consumers, businesses, and organizations may purchase green energy in order to support further development, help reduce the environmental impacts of conventional electricity generation, and increase their nation’s energy independence. Renewable energy certificates (green certificates or green tags) have been one way for consumers and businesses to support green energy.
Although not permitted under the US National Electric Code, it is technically possible to have a “plug and play” PV microinverter. A recent review article found that careful system design would enable such systems to meet all technical, though not all safety requirements.[112] There are several companies selling plug and play solar systems available on the web, but there is a concern that if people install their own it will reduce the enormous employment advantage solar has over fossil fuels.[113]

The locations with highest annual solar irradiance lie in the arid tropics and subtropics. Deserts lying in low latitudes usually have few clouds, and can receive sunshine for more than ten hours a day.[86][87] These hot deserts form the Global Sun Belt circling the world. This belt consists of extensive swathes of land in Northern Africa, Southern Africa, Southwest Asia, Middle East, and Australia, as well as the much smaller deserts of North and South America.[88] Africa's eastern Sahara Desert, also known as the Libyan Desert, has been observed to be the sunniest place on Earth according to NASA.[89][90]
×