The energy it calculates is in kWh per year, the diameter of the wind turbine rotor is in meters, the wind speed is annual average for the turbine hub height in m/s. The equation uses a Weibull wind distribution with a factor of K=2, which is about right for inland sites. An overall efficiency of the turbine, from wind to electrical grid, of 30% is used. That is a reasonable, real-world efficiency number. Here is a table that shows how average annual wind speed, turbine size, and annual energy production relate:


The Solar updraft tower is a renewable-energy power plant for generating electricity from low temperature solar heat. Sunshine heats the air beneath a very wide greenhouse-like roofed collector structure surrounding the central base of a very tall chimney tower. The resulting convection causes a hot air updraft in the tower by the chimney effect. This airflow drives wind turbines placed in the chimney updraft or around the chimney base to produce electricity. Plans for scaled-up versions of demonstration models will allow significant power generation, and may allow development of other applications, such as water extraction or distillation, and agriculture or horticulture. A more advanced version of a similarly themed technology is the Vortex engine which aims to replace large physical chimneys with a vortex of air created by a shorter, less-expensive structure.
Green-e is a voluntary certification program for renewable electricity products. The Green-e program establishes consumer protection and environmental standards for electricity products, and verifies that these products meet the standards. The Green-e logo certifies that at least half the power supplied is from renewable sources. Many products will carry the Green-e logo, and the best way to find the most environmentally sensitive providers is by doing some comparison research. To find out which Green-e certified products are available in your state, visit Green-e's electric choices page. Questions about particular providers can be directed to the Center for Resources Solutions, which administers the Green-e program, at (415) 561-2100.
The life-cycle greenhouse-gas emissions of solar power are in the range of 22 to 46 gram (g) per kilowatt-hour (kWh) depending on if solar thermal or solar PV is being analyzed, respectively. With this potentially being decreased to 15 g/kWh in the future.[121] For comparison (of weighted averages), a combined cycle gas-fired power plant emits some 400–599 g/kWh,[122] an oil-fired power plant 893 g/kWh,[122] a coal-fired power plant 915–994 g/kWh[123] or with carbon capture and storage some 200 g/kWh, and a geothermal high-temp. power plant 91–122 g/kWh.[122] The life cycle emission intensity of hydro, wind and nuclear power are lower than solar's as of 2011 as published by the IPCC, and discussed in the article Life-cycle greenhouse-gas emissions of energy sources. Similar to all energy sources were their total life cycle emissions primarily lay in the construction and transportation phase, the switch to low carbon power in the manufacturing and transportation of solar devices would further reduce carbon emissions. BP Solar owns two factories built by Solarex (one in Maryland, the other in Virginia) in which all of the energy used to manufacture solar panels is produced by solar panels. A 1-kilowatt system eliminates the burning of approximately 170 pounds of coal, 300 pounds of carbon dioxide from being released into the atmosphere, and saves up to 105 gallons of water consumption monthly.[124]

A Darrieus type vertical axis wind turbine (the egg-beater type) can in theory work almost as good as a horizontal axis turbine. Actual measurement of one of the better designs out there, the UGE VisionAir5, does not bear that out though: It measures in at a pitiful 11% efficiency at 11 m/s wind speed, while a Bergey Excel-6 HAWT clocks in at 22% efficiency for that same wind speed, twice as much. You can read about it in Paul Gipe’s article.  Besides efficiency issues, a Darrieus VAWT unfortunately has a number of inherent issues that put them at a disadvantage: Since they are usually tall and relatively narrow structures the bending forces on their main bearing (at the bottom) are very large. There are similar issues with the forces on the blades. This means that to make a reliable vertical axis turbine takes more material, and more expensive materials, in comparison to a horizontal type turbine. For comparison, that same UGE VisionAir5 weighs 756 kg vs. the Bergey Excel-6 at 350 kg. Keep in mind that the UGE turbine only sweeps about half the area of the Bergey, the latter is a much larger turbine! This makes VAWTs inherently more expensive, or less reliable, or both.
I mounted this turbine in my back yard on the recommended schedule 40 galvanized pipe at about 20' high. My location does not get consistent wind from one direction which is the only way this turbine will spin. Even in gusty conditions of 15-20 mph the turbine rarely spins more than a few revolutions and has not produced any measurable power after a month. If you don't have a steady wind from one direction this turbine will not produce any power at all. You would be better off with a vertical turbine or one with larger blade surface area. The specs say 8 mph start up, that means a consistent 8 mph wind from a single direction. For the money you would be better off with a single 80 watt solar panel.
Worldwide growth of photovoltaics has averaged 40% per year from 2000 to 2013[35] and total installed capacity reached 303 GW at the end of 2016 with China having the most cumulative installations (78 GW)[36] and Honduras having the highest theoretical percentage of annual electricity usage which could be generated by solar PV (12.5%).[36][35] The largest manufacturers are located in China.[37][38]
This listing is for: One Heavy 100 Amp Rectifier ---Heavy quality rectifier intended for wind turbine rated for 100 amps continuous usage. ---This item is used to convert 3 phase AC to DC. This heavy rectifier is built into a heat sink body that allows unit to keep cool. ---Rectifier has spade terminals which will make for a clean and secure installation. No wondering if your wiring is going to come loose. ---Two mounting holes to secure the body of the rectifier to your mounting box ---This item is not to me confused with a blocking diode to be used in DC motor applications or with solar. Powered by [eBay Turbo Lister] (http://pages.ebay.com/turbo_lister/) The free listing tool. List your items fast and easy and manage your active items. Froo www.froo.

Enhanced geothermal systems (EGS) are a new type of geothermal power technologies that do not require natural convective hydrothermal resources. The vast majority of geothermal energy within drilling reach is in dry and non-porous rock.[161] EGS technologies "enhance" and/or create geothermal resources in this "hot dry rock (HDR)" through hydraulic stimulation. EGS and HDR technologies, such as hydrothermal geothermal, are expected to be baseload resources which produce power 24 hours a day like a fossil plant. Distinct from hydrothermal, HDR and EGS may be feasible anywhere in the world, depending on the economic limits of drill depth. Good locations are over deep granite covered by a thick (3–5 km) layer of insulating sediments which slow heat loss.[162] There are HDR and EGS systems currently being developed and tested in France, Australia, Japan, Germany, the U.S. and Switzerland. The largest EGS project in the world is a 25 megawatt demonstration plant currently being developed in the Cooper Basin, Australia. The Cooper Basin has the potential to generate 5,000–10,000 MW.
Materials for wind turbine parts other than the rotor blades (including the rotor hub, gearbox, frame, and tower) are largely composed of steel. Modern turbines use a couple of tons of copper for generators, cables, and such.[52] Smaller wind turbines have begun incorporating more aluminum based alloys into these components in an effort to make the turbines lighter and more efficient, and may continue to be used increasingly if fatigue and strength properties can be improved. Prestressed concrete has been increasingly used for the material of the tower, but still requires much reinforcing steel to meet the strength requirement of the turbine. Additionally, step-up gearboxes are being increasingly replaced with variable speed generators, increasing the demand for magnetic materials in wind turbines.[46] In particular, this would require an increased supply of the rare earth metal neodymium.
My system has been installed for about a year now. When I first contracted with Envismart, the sales rep was very available and eager to help with my questions but after the installation, he was very hard to make contact with, seldom returned my calls, and when he did seemed to tell me what he thought I wanted hear and very seldom followed through. The system had a shaky start, it died after one day and after two new inverters and several optimizers over several months of on again, off again operation it seems to be running smoothly, at least for the last few months. Customer support was not very good, to be kind, but the service personnel that came out were prompt and there when they said they would be and very open about what the problems were and quickly fixed them. I was told my recurring system problems were a little unusual and I have to take their word on that but they gave me their personnel cell numbers and told me to call them when I couldn't get Customer Support to call - and when I called them, they came through and got me serviced a lot more quickly. They are the main reason I rated the company a 3.I have to say, the last month or so, it seems like the company is starting to work on changing its image. I have been called on several occasions by the "Quality Assurance" group at their initiation and asked if everything was OK with my system and I usually had an issue about something (admittedly, sometimes very minor). They always followed through with answers and corrected my concerns which was a big change from my previous experiences. I want to encourage them to continue improving their Customer Support after the sale in this manner as that is the real reputation for their company. I am still reserving my opinion but I am very much encouraged by their recent efforts - Keep it up!... read more

Wind turbines do work; put them in nice, smooth air and their energy production is quite predictable (we will get to predicting it a bit further on in this story). The honest manufacturers do not lie or exaggerate, their turbines really can work as advertised in smooth, laminar airflow. However, put that same turbine on a 40 feet tower and even if the annual average wind speed is still 5 m/s at that height, its energy production will fall far short of what you would predict for that value. How short is anybody’s guess, that is part of the point; it is impossible to predict the effect of turbulence other than that it robs the energy production potential of any wind turbine. Roof tops, or other locations on a house, make for poor turbine sites. They are usually very turbulent and on top of that their average wind speeds are usually very low.
The New Zealand Parliamentary Commissioner for the Environment found that the solar PV would have little impact on the country's greenhouse gas emissions. The country already generates 80 percent of its electricity from renewable resources (primarily hydroelectricity and geothermal) and national electricity usage peaks on winter evenings whereas solar generation peaks on summer afternoons, meaning a large uptake of solar PV would end up displacing other renewable generators before fossil-fueled power plants.[127]

Innovative programs around the country now make it possible for all environmentally conscious energy consumers to support renewable energy directly by participating in the "green" power market. The willingness to pay for the benefits of increasing our renewable energy supplies can be tapped within any market structure and by any size or type of energy consumer.
http://WINDENERGY7.com - Home Wind Generator for sale and Home Wind Generator kits from WindEnergy7 and Ohio manufacturer of home energy products. If you are looking for a home wind generator, home wind generator system, home vertical wind generator, small home wind generator, home wind generator kit, home wind generator plans, home wind electric generator, home wind power generator, rooftop wind generator, then come to our website to SEE LATEST VIDEOS: http://WindEnergy7.com
Perfect for camping tailgating or when you need Perfect for camping tailgating or when you need power on the go. The FIRMAN P01001 generator features 1050 starting Watts and 1300 running watts. Power is supplied by our Max Pro Series 80cc FIRMAN engine which runs cool and efficient thanks to its Phoenix Fat Head Block. Our Whisper Series ...  More + Product Details Close

Solar energy, radiant light and heat from the sun, is harnessed using a range of ever-evolving technologies such as solar heating, photovoltaics, concentrated solar power (CSP), concentrator photovoltaics (CPV), solar architecture and artificial photosynthesis.[49][50] Solar technologies are broadly characterized as either passive solar or active solar depending on the way they capture, convert and distribute solar energy. Passive solar techniques include orienting a building to the Sun, selecting materials with favorable thermal mass or light dispersing properties, and designing spaces that naturally circulate air. Active solar technologies encompass solar thermal energy, using solar collectors for heating, and solar power, converting sunlight into electricity either directly using photovoltaics (PV), or indirectly using concentrated solar power (CSP).
A: Modern solar panels typically last twenty to thirty years before there’s a noticeable increase in output loss. Most residential solar providers offer a 20- to 25-year warranty, but many such warranties only guarantee a certain power output (e.g., a guarantee of 80% output for twenty years). Carefully read through the fine print to make sure you understand the warranty and what it covers.

As of 2014, offshore wind power amounted to 8,771 megawatt of global installed capacity. Although offshore capacity doubled within three years (from 4,117 MW in 2011), it accounted for only 2.3% of the total wind power capacity. The United Kingdom is the undisputed leader of offshore power with half of the world's installed capacity ahead of Denmark, Germany, Belgium and China.
“Trump’s Keystone XL Tar Sands Oil Pipeline Promise, Unkept and Undone” • The federal judge for the District of Montana who overturned permit for the Keystone XL pipeline issued an order that all but guarantees the project will die another death by a thousand cuts. He ordered a complete do-over on economic and environmental impacts. [CleanTechnica]
In stand alone PV systems batteries are traditionally used to store excess electricity. With grid-connected photovoltaic power system, excess electricity can be sent to the electrical grid. Net metering and feed-in tariff programs give these systems a credit for the electricity they produce. This credit offsets electricity provided from the grid when the system cannot meet demand, effectively trading with the grid instead of storing excess electricity. Credits are normally rolled over from month to month and any remaining surplus settled annually.[111] When wind and solar are a small fraction of the grid power, other generation techniques can adjust their output appropriately, but as these forms of variable power grow, additional balance on the grid is needed. As prices are rapidly declining, PV systems increasingly use rechargeable batteries to store a surplus to be later used at night. Batteries used for grid-storage stabilize the electrical grid by leveling out peak loads usually for several minutes, and in rare cases for hours. In the future, less expensive batteries could play an important role on the electrical grid, as they can charge during periods when generation exceeds demand and feed their stored energy into the grid when demand is higher than generation.
Small wind turbines may be used for a variety of applications including on- or off-grid residences, telecom towers, offshore platforms, rural schools and clinics, remote monitoring and other purposes that require energy where there is no electric grid, or where the grid is unstable. Small wind turbines may be as small as a fifty-watt generator for boat or caravan use. Hybrid solar and wind powered units are increasingly being used for traffic signage, particularly in rural locations, as they avoid the need to lay long cables from the nearest mains connection point.[60] The U.S. Department of Energy's National Renewable Energy Laboratory (NREL) defines small wind turbines as those smaller than or equal to 100 kilowatts.[61] Small units often have direct drive generators, direct current output, aeroelastic blades, lifetime bearings and use a vane to point into the wind.
Taken together, the generation and distribution of electric power in the United States is an astonishingly complex undertaking. Utilities may generate their own power or buy it from other utilities; that power travels over a grid of transformers and high- and low-voltage lines to your house. Ownership of utilities varies from nonprofits to cooperatives to for-profits. Federal regulators ultimately oversee the grid. Amazingly, when you flip a switch, electricity is there.
Nearly all the gasoline sold in the United States today is mixed with 10% ethanol,[128] and motor vehicle manufacturers already produce vehicles designed to run on much higher ethanol blends. Ford, Daimler AG, and GM are among the automobile companies that sell "flexible-fuel" cars, trucks, and minivans that can use gasoline and ethanol blends ranging from pure gasoline up to 85% ethanol. By mid-2006, there were approximately 6 million ethanol compatible vehicles on U.S. roads.[129]

As competition in the wind market increases, companies are seeking ways to draw greater efficiency from their designs. One of the predominant ways wind turbines have gained performance is by increasing rotor diameters, and thus blade length. Retrofitting current turbines with larger blades mitigates the need and risks associated with a system-level redesign. As the size of the blade increases, its tendency to deflect also increases. Thus, from a materials perspective, the stiffness-to-weight is of major importance. As the blades need to function over a 100 million load cycles over a period of 20–25 years, the fatigue life of the blade materials is also of utmost importance. By incorporating carbon fiber into parts of existing blade systems, manufacturers may increase the length of the blades without increasing their overall weight. For instance, the spar cap, a structural element of a turbine blade, commonly experiences high tensile loading, making it an ideal candidate to utilize the enhanced tensile properties of carbon fiber in comparison to glass fiber.[47] Higher stiffness and lower density translates to thinner, lighter blades offering equivalent performance. In a 10 (MW) turbine—which will become more common in offshore systems by 2021—blades may reach over 100 m in length and weigh up to 50 metric tons when fabricated out of glass fiber. A switch to carbon fiber in the structural spar of the blade yields weight savings of 20 to 30 percent, or approximately 15 metric tons.[48]


All these electrical machines are electromechanical devices that work on Faraday’s law of electromagnetic induction. That is they operate through the interaction of a magnetic flux and an electric current, or flow of charge. As this process is reversible, the same machine can be used as a conventional electrical motor for converting the electrical power into mechanical power, or as a generator converting the mechanical power back into the electrical power.
Within emerging economies, Brazil comes second to China in terms of clean energy investments. Supported by strong energy policies, Brazil has one of the world’s highest biomass and small-hydro power capacities and is poised for significant growth in wind energy investment. The cumulative investment potential in Brazil from 2010 to 2020 is projected as $67 billion.[155]
The energy it calculates is in kWh per year, the diameter of the wind turbine rotor is in meters, the wind speed is annual average for the turbine hub height in m/s. The equation uses a Weibull wind distribution with a factor of K=2, which is about right for inland sites. An overall efficiency of the turbine, from wind to electrical grid, of 30% is used. That is a reasonable, real-world efficiency number. Here is a table that shows how average annual wind speed, turbine size, and annual energy production relate:
The expansion is thanks largely to innovation on the policy front, which has opened up opportunities in regulated electricity markets. The number of corporate renewable energy deals signed under utility green tariff programs continues to grow, representing around 25 percent of corporate renewables procurement so far this year. At the same time, utilities are incorporating corporate renewables into their long-term planning — and thinking about solutions beyond green tariffs to better meet the needs of existing corporate customers and smaller loads.
Between maintenance and repairs, it would greatly help and keep your cost down if you can do some of the work yourself: Being able to safely tilt the turbine tower up or down will save you money. Understanding how the turbine works, how to stop it safely, how to trouble-shoot at least the minor issues can keep you in the black. We understand that installing a wind turbine is not for everyone. In fact, towers are dangerous, and for a good installation the devil is in the details. An experienced installer can make a real difference in putting up a turbine that will work better, and be more reliable over time. We really encourage you to have a professional installer to do the initial installation. However, throwing up your hands and calling your installer for routine maintenance, or every time there is a minor issue, will likely make you an unhappy wind turbine owner (even if it is your installer’s dream).

†Offer is available to Texas residential customers who enroll using the Promotion Code “NIGHTSFREE”. Plan bills a monthly Base Charge, an Energy Charge, and passes through Utility Transmission and Distribution delivery charges. Energy Charges for usage consumed between 9pm and 7am each day is credited back on your bill. The utility charges, including delivery charges for night time hours, are passed through at cost and aggregated on your bill. See Electricity Facts Label for details.

The International Geothermal Association (IGA) has reported that 10,715 MW of geothermal power in 24 countries is online, which is expected to generate 67,246 GWh of electricity in 2010.[131] This represents a 20% increase in geothermal power online capacity since 2005. IGA projects this will grow to 18,500 MW by 2015, due to the large number of projects presently under consideration, often in areas previously assumed to have little exploitable resource.[131]
The energy payback time (EPBT) of a power generating system is the time required to generate as much energy as is consumed during production and lifetime operation of the system. Due to improving production technologies the payback time has been decreasing constantly since the introduction of PV systems in the energy market.[128] In 2000 the energy payback time of PV systems was estimated as 8 to 11 years[129] and in 2006 this was estimated to be 1.5 to 3.5 years for crystalline silicon PV systems[121] and 1–1.5 years for thin film technologies (S. Europe).[121] These figures fell to 0.75–3.5 years in 2013, with an average of about 2 years for crystalline silicon PV and CIS systems.[130]
As of 2014, offshore wind power amounted to 8,771 megawatt of global installed capacity. Although offshore capacity doubled within three years (from 4,117 MW in 2011), it accounted for only 2.3% of the total wind power capacity. The United Kingdom is the undisputed leader of offshore power with half of the world's installed capacity ahead of Denmark, Germany, Belgium and China.
Materials for wind turbine parts other than the rotor blades (including the rotor hub, gearbox, frame, and tower) are largely composed of steel. Modern turbines use a couple of tons of copper for generators, cables, and such.[52] Smaller wind turbines have begun incorporating more aluminum based alloys into these components in an effort to make the turbines lighter and more efficient, and may continue to be used increasingly if fatigue and strength properties can be improved. Prestressed concrete has been increasingly used for the material of the tower, but still requires much reinforcing steel to meet the strength requirement of the turbine. Additionally, step-up gearboxes are being increasingly replaced with variable speed generators, increasing the demand for magnetic materials in wind turbines.[46] In particular, this would require an increased supply of the rare earth metal neodymium.
“[The maps] suggest that our 100 percent renewable energy purchasing goal — which relies on buying surplus renewable energy when it’s sunny and windy, to offset the lack of renewable energy supply in other situations — is an important first step toward achieving a fully carbon-free future,” Michael Terrell, Google’s head of energy markets, wrote in a blog post. “Ultimately, we aspire to source carbon-free energy for our operations in all places, at all times.”

In 2010, the International Energy Agency predicted that global solar PV capacity could reach 3,000 GW or 11% of projected global electricity generation by 2050—enough to generate 4,500 TWh of electricity.[40] Four years later, in 2014, the agency projected that, under its "high renewables" scenario, solar power could supply 27% of global electricity generation by 2050 (16% from PV and 11% from CSP).[2]
×